|
GENERAL
|
BE14, is an excellent 100% solid epoxy primer for concrete surfaces. BE14, is ecologically and designed for application directly On wet and dry surfaces It is compatible with new(green) or aged Concrete, bare concrete or existing coatings that are firmly adhered To surface.
|
|
总述
|
BE14 是一种固含量为100%的优良的环氧底漆，用于混凝土的外表。BE14 可间接涂装在湿的或干的外表，与新旧混凝土相容。与袒露的混土或有涂层的混凝土能牢牢附着。
|
|
FEATRURES
|
NO HARMFUL SOLVENT VAPOURS.
NON-FLAMMABLE.
Good chemical resistance
No more problems with DEW POINT.
Fast drying
Excellent substrate and intercoat adhesion either on wet or dry surface.
Cost savings on surface preparation.
|
|
产物特征
|
无有害蒸发掉物
必不可燃
优秀的耐检查是否性
无露点题目大全
快干
不顾是湿的仍是干的看上去，与基低或平台铝层有良好率的胶接力
节流本身正确处理挣到
|
|
RECOMMENDED
|
USES TYPICAL STRUCTURES Concrete pylons; Sea walls; Pools and Sea aquarium; Dams and Concrete locks; Aqueducts; Concrete tanks-water, Fuel or Grains; Tunnels; etc. SHIPS, OFFSHORE Decks, Chain lockers, Tower bridge, etc. PIPE COATINGS Suitable for direct application on exterior and interior potable water Pipes lines. Sew lines. Excellent chemical resistance.
|
|
保举用处
|
典范布局
混凝土的标塔，海堤，池子，防水层，大坝，水闸，高架水道，混凝储水罐，燃料或各类的贮存罐，地道。船只，口岸船面，链锁装配，塔，桥等。管道涂层合用于饮水管道表里壁的涂层，杰出的耐化学性。
|
|
SPECIFICATION DATA
|
|
技 术 参 数
|
|
Binder Type/Pigment Type
|
Modified epoxy/Amine composite- Chemical resistant pigments
|
|
基料范例/颜料范例
|
改性环氧/复合胺/耐化学型颜料
|
|
Colors
|
BE1409(clear), BE1410(light grey) BE1411(dark grey)
|
|
色彩
|
BE14 09通明，BE14 10浅灰色，BE1411深灰
|
|
Finish
|
Gloss
|
|
外表
|
高光
|
|
Mixing ratio
|
4base) to 1(curing agent) by weight, 3.3(base) to1(curing agent) by volume
|
|
夹杂比率
|
分量比 4(基料)：1(固化剂)
体积比 3.3(基料)：1(固化剂)
|
|
Curing agent
|
CA24
|
|
固化剂
|
CA24
|
|
Specific gravity(mixture-BE1409)
|
1.09±0.02Kg/ Lt
|
|
比重
|
1.09±0.02千克/升
|
|
Solid by Volume
|
100%(theoretical)
|
|
体积固体份
|
100%(实际值)
|
|
Pot Life
|
10 minutes at 23℃(73.4℉)
|
|
夹杂利用期
|
10分钟，23℃(73.4℉)
|
|
Flash point(Abel)
|
Base: >100℃(>212℉);Curing agent: >100℃(>212℉)
|
|
闪点
|
基料：>100℃；固化剂：>100℃
|
|
Theoretical covering capability
|
4.6Sq.m/Kg(22.4 q.ft/Lb) at 200 microns (8 mils)
|
|
实际笼盖才能
|
4.6平方米/千克，200um
|
|
Typical film thickness per coat
|
Wet:200microns(8mils); Dry:200 mircons (8mils)
|
|
单层膜厚
|
湿膜：200um，干膜：200um
|
|
Application method
|
Brush, Roller
|
|
施工方式
|
刷子，辊子
|
|
Thinner
|
Material: none -Cleaning: EURO-thinner TH03
|
|
浓缩剂
|
资料：无；洗濯：TH03
|
|
VOC
|
Does not contain. It is a 100% solids epoxy product.
|
|
挥发性无机化合物
|
不含，为100%的固体环氧产物。
|
|
Drying time
|
Surface dry: approx. 3 hours (at 23℃ （73.4℉） and 50% relative humidity)
|
|
枯燥时候
|
表干：3小时，在23°C和50%绝对湿度下。
|
|
Overcoating time
|
Min:16 hours at 23℃ ;Max: 7 days.
|
|
重涂时候
|
最短：16小时(23°C)，最长：7天.
|
|
Ambient temperature
|
Min: >0℃(32℉)-Max: Not applicable. Substrate is the important factor when applying below 0℃(32℉), a different cure is required.
|
|
情况温度
|
最低：>0°C，最高：无，基底是主要身分。当于0℃以下涂覆时，请求差别的固化方式。
|
|
Substrate temperature
|
Min:0℃(32℉)- Max:50℃(122℉)
|
|
底材温度
|
最低：0°C，最高：50°C
|
|
Storage and Shelf life
|
The product should be kept in a cool well ventilated places
protected from high temperatures.
Container MUST BE kept tightly closed.
Shelf life:1 year
|
|
包装和贮存刻日
|
产物保管于阴凉、透风杰出的处所，避
免太高的温度。容器必须安稳密封.贮存期:1年
|
|
APPLICATION GUIDE
|
|
施 工 指 导
|
|
SURFACE PREPARATION
|
BE14, is designed for application over concrete surfaces pre-treated by Hydrojetting, mechanical cleaning, and wet or dry abrasive blasting to standards specified. Coating performance is, in general, proportional to degree of surface preparation.
|
|
外表处置
|
BE14，用于经太高压水或机器洗濯的混凝土外表 。普通，涂层的机能与外表处置的级别成反比
|
|
APPLICATION
|
BE14, can be applied, by brush and roller. Ventilation It is very important for the safety of the applicator that good ventilation be provided to all portions of the area.
|
|
施工
|
BE14，可接纳刷涂、辊涂
透风
功课区的各个部位坚持杰出的透风对操纵职员的宁静长短常主要的。
|
|
SAFETY
|
WARNING: Avoid breathing vapors. Do not get in eyes on skin or clothing, Use ear ,eye and skin protective equipment. Use appropriate respirator. Wash skin thoroughly after use and water. Launder clothing before reuse. If not breathing gives artificial respiration, preferably mouth-to-mouth, and call physician.
BURNS: Exothermic reaction causes product to heat which is normal.
Be careful handling after mixing product. Use gloves.
FIRST AID: In case of eye contact immediately flush with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash skin contact area with soap.
|
|
宁静办法
|
正告：防止吸入汽雾。请勿涉及眼睛皮肤。要利用眼、耳、皮肤的防护器具，利用适合的面具。利用后用净水完全的洗濯皮肤。衣物再次利用前要洗濯。若是不呼吸要停止野生呼吸，最好嘴对嘴，并请大夫处置。
灼伤：放热反映会使产物变热，超越一般程度。在夹杂后要谨慎处置。利用手套。
抢救：若是不慎打仗了眼睛，当即用净水冲刷最少15分钟，并脱去净化的衣鞋，用番笕洗濯打仗后的皮肤。
|
|
DISCLAMER
|
This is not a specification and all information is given in good faith. Every values presented as Theoretical were calculated from the product formula If requested, Euronavy can inform any internal measurement method used to determinate any given value presented. Since conditions of use are beyond the manufacturers control information contained herein is without warranty, implied or otherwise, and final determination of the suitability of any information or material for the use contemplated is the sole responsibility of user. The product is intended for professional use only. In case of any doubt, contact your local agent.
|
|
提请注重
|
此文件不是正式的手艺文件，所列出的信息是靠得住的。供给的每一个数值都是作为实际数据从产物的配方入彀算出来的。若是须要，Euronavy能够奉告任何上述给出数据的外部经常利用丈量肯定方式。因为利用前提非出产商所能节制，这里的信息不作为包管。产物仅限于专业职员利用。若有任何题目，请与本地相干机构接洽。
|
